Short answer: before you hire anyone to spray foam in your house, ask these eight questions: does each spot really need foam, which product and how thick, can you see the product's data sheets, when do you leave and when can you come back, how is the work area ventilated and sealed off, what prep and removal is included, how the foam will be covered, and can you see license and insurance proof with a written scope. A good contractor answers all of them without hesitating.
I'm Joe Giordano, and I've been insulating homes in Nassau and Suffolk since 2004. People call me asking for spray foam all the time. I install it when the job needs it, and I often recommend cellulose instead. These are the questions I'd ask if I were the homeowner.
1. Does this spot actually need spray foam?
Spray foam earns its cost in specific places: rim joists, shallow sloped or cathedral ceilings, some crawl space and basement walls, and odd cavities where air sealing and insulation have to happen together. On an open attic floor, blown-in cellulose or fiberglass over a sealed attic floor usually does the job for less.
Ask the contractor why each area needs foam and what the cellulose or fiberglass option would be. If the answer is "foam is best everywhere," keep asking. Our cellulose vs spray foam article goes through where each one fits.
2. Which product, open-cell or closed-cell, and how thick in each area?
Open-cell foam is soft and lets water vapor through. Closed-cell foam is denser, insulates more per inch, and at enough thickness slows water vapor. They aren't interchangeable.
The estimate should name the manufacturer and product, say open- or closed-cell for each area, and give the thickness and the R-value it reaches. Compare that to the level for that part of the house in our Long Island R-value guide. EPA's contractor checklist for spray foam tells installers to record the product names and system numbers and to spray in layers at the thickness the manufacturer specifies.
3. Can I see the product's data sheets?
Ask for the technical data sheet, the Safety Data Sheet (SDS) and the manufacturer's installation instructions for the product. EPA's checklist expects contractors to keep these on site and to follow the manufacturer's instructions for application. You don't need to read every page, but a contractor who can't produce them is a red flag.
4. When do we need to leave, and when can we come back?
The main health concern with spray foam is during spraying and curing. The chemicals involved, including isocyanates, need protection and ventilation while the foam is applied and cures. OSHA explains the hazard.
EPA's checklist says occupants should stay away from the work area while the foam is applied and cures, and until the space has been ventilated and cleaned. It also says recommended re-occupancy times vary by product, so contractors should get the time for their specific product from the manufacturer. Ask for that time in writing, along with which parts of the house you can use while the work is going on.
5. How will the work area be ventilated and sealed off?
EPA's checklist describes what a careful installer does: set up a work zone, turn off or isolate the heating and cooling system, cover air handlers and vents with plastic, and run exhaust fans so air flows out of the work area, then keep them running while the foam cures. Ask the contractor to walk you through their plan for your house, including any furnace, boiler or water heater near the work.
6. What prep and removal are included?
Foam has to go on clean, dry framing or sheathing, so old insulation is usually removed where foam goes. Leaks have to be fixed first; foam doesn't fix a roof or plumbing leak, and EPA's guidance is that "the key to mold control is moisture control" (EPA mold and moisture guide).
The estimate should say what comes out, how it's disposed of, how floors and belongings are protected, and how the area is cleaned up afterward. Our guide on when to remove old attic insulation explains what's worth keeping.
7. Will the foam be covered, or left exposed?
Foam in a living space, basement or attic generally needs a code-approved covering, such as drywall, unless the product is rated for that exposed use. The DOE Building America basement wall checklist notes that exposed foam must be covered with an ignition barrier or a fire-rated assembly. Ask whether the foam needs a covering in each area, who installs it, and whether it's in the price. Your building department decides what's required on a permitted job.
8. Can I see proof of license and insurance, and a written scope?
Nassau and Suffolk each license home improvement contractors through their consumer affairs offices. You can check a license with Suffolk County Consumer Affairs or use Nassau County's home improvement checklist. Ask for a certificate of insurance too. Our guide to choosing an insulation contractor on Long Island covers licenses, insurance and contract terms in more detail.
Then get the scope in writing: each area, the product and thickness, the R-value, the prep and removal, the covering, cleanup and the re-entry time. That's what you compare when you have more than one quote.
Frequently asked questions
Is spray foam worth it on Long Island?
In the right spots, yes. Rim joists and shallow sloped ceilings are the most common. For most open attic floors and closed walls, cellulose is the better value. See fiberglass vs spray foam for a side-by-side.
Can spray foam go over old insulation?
Usually no. Foam needs to stick to clean framing or sheathing, so the old insulation generally comes out where the foam goes.
Do I need spray foam to stop ice dams?
Not usually. Ice dams start with warm air leaking into the attic. Sealing those leaks and blowing insulation to full depth on the attic floor handles most of it. See preventing ice dams.
Does Paramount Insulation install spray foam?
Yes, when the job truly needs it. I'll tell you when it doesn't. See our spray foam insulation page.
Talk it through with Joe
Call or text me at (631) 492-0214, Monday to Saturday, 7 AM to 7 PM. I answer my own phone and call back the same day. Or request a free estimate and diagnosis. I'll go into the attic and crawl space, measure, use a thermal camera, and tell you where foam makes sense and where something else would do the job better. We work across Nassau and Suffolk; find your town on our service areas page.