Short answer: the rim joist is the band of framing that sits on top of your foundation wall and carries the edge of the first floor. In a lot of older Long Island houses it's bare wood with gaps along the sill, so cold outside air comes straight into the basement and under the floors. Sealing and insulating it, usually with closed-cell spray foam or rigid foam board sealed at the edges, is often the first thing I recommend in a basement or crawl space.
I'm Joe Giordano, and I've been insulating homes in Nassau and Suffolk since 2004. When someone tells me the floor is cold along the outside walls, the rim joist is the first place I look.
What is a rim joist?
Walk down to an unfinished basement and look up where the foundation wall meets the wood. The flat board running around the edge of the house, capping the ends of the floor joists, is the rim joist (also called the band joist or rim board). It sits on the sill plate, which sits on the foundation.
Between each pair of floor joists there's a small open bay of rim joist. A typical house has dozens of them, and each one has seams where air can get in: between the foundation and the sill, between the sill and the rim board, and between the rim board and the subfloor above.
Why is it the coldest spot in the basement?
- It's above ground. The rim joist is exposed to outside air on the other side of the siding, unlike the foundation wall below it, which is mostly in the ground.
- It's usually bare. In many older homes nothing was ever put there. Sometimes there's a loose fiberglass batt stuffed in, which doesn't stop air.
- It's full of gaps. Every seam and every pipe, wire or vent that passes through the rim is a path for cold air, and sometimes for mice.
How do I know my rim joist needs work?
- Floors feel cold along the outside walls, especially over the basement or crawl space
- You feel a draft at the top of the foundation wall on a windy day
- You see daylight, spider webs or droppings along the sill
- There's frost or dampness on the rim board in the coldest weeks
- Pipes that run along the top of the foundation wall have frozen before
At the free estimate, I go down into the basement or crawl space with a thermal camera. Cold rim bays show up clearly, and so do the leaks around them.
What does New York's code say about rim joists?
The 2025 Energy Conservation Construction Code of New York State covers rim joists in its air barrier and insulation table (Table R402.5.1.1). It says:
- Rim joists must include an air barrier.
- The joints between the rim board and the sill plate, and between the rim board and the subfloor, must be air sealed.
- The insulation must stay in permanent contact with the rim board.
The same table calls for sealing the joint between the foundation and the sill plate. These rules apply to new construction and to parts of an existing home that are altered (Section R503.1.1.6). For the basement walls below the rim, the Zone 4 options are in our Long Island R-value guide. Your building department decides what applies to a permitted job.
How is a rim joist sealed and insulated?
There are two common ways. Both put the insulation tight against the rim board and seal the edges.
Closed-cell spray foam
Closed-cell foam is sprayed directly onto the rim board, the sill and the seams, so it air seals and insulates in one step. It's one of the spots where I think spray foam is worth it. It's a chemical product mixed on site, so the household stays out of the work area while it's sprayed and until the product's re-entry time. Follow the foam manufacturer's re-entry instructions; I tell you the time for the product I'm using. OSHA explains the isocyanate hazard, and our guide to hiring a spray foam contractor lists the questions to ask.
Rigid foam board, cut to fit
Rigid foam board is cut to fit each bay and pressed against the rim board, then every edge is sealed with caulk or canned foam. The DOE Building America guide for floors above unconditioned basements and crawl spaces describes both this method and spray foam. It takes longer, but there's no cure time.
Why not just a fiberglass batt?
A batt stuffed into the bay on its own doesn't stop air, and warm, damp basement air can reach the cold rim board behind it and condense. The DOE Building America basement wall checklist calls for closed-cell spray foam or rigid insulation board installed directly against the rim joist, with seams sealed. A batt can go over the foam if more R-value is wanted.
What gets checked before the rim joist is covered?
- Water. Wet or rotted wood, active leaks, or soil and mulch piled against the siding get fixed first. Insulation doesn't fix a leak. EPA's guidance is that "the key to mold control is moisture control" (EPA mold and moisture guide).
- Pests. Signs of termites or carpenter ants mean a call to a pest professional before anything is covered.
- Fire protection. Exposed foam in a basement generally needs a code-approved ignition barrier or a fire-rated covering, such as drywall, unless the product is rated for that use. The Building America checklist notes the same rule.
- Vents and combustion appliances. Dryer vents, exhaust pipes and gas lines that pass through the rim stay clear, and sealing around them uses materials rated for the job.
Does this apply to crawl spaces too?
Yes. A crawl space has the same rim joist on top of its foundation wall. If the crawl space is being sealed and insulated at the walls, the rim joist is part of that job. If it's vented and the floor above is insulated instead, the rim bays still leak air into the cold space under the house. Our article on crawl space encapsulation vs insulation explains the two approaches, and the crawl space insulation page shows what we do.
Frequently asked questions
Should I insulate the rim joist if my basement is unfinished?
Usually, yes. Even in an unfinished basement, the rim joist is where outside air gets in, and sealing it helps the floors above and any pipes that run along the top of the wall.
Will sealing the rim joist stop my pipes from freezing?
It cuts the cold air hitting pipes that run along the top of the foundation wall. It doesn't replace pipe insulation or heat in the space. See preventing frozen pipes.
Can I do it myself?
Cutting rigid foam and sealing the edges is a job a handy homeowner can do, as long as nothing is wet or damaged and the foam is covered where the code requires it. Spray foam kits carry real chemical exposure risks; read the label and the OSHA guidance first.
Is rim joist work done with the rest of the basement?
It can be done on its own or as part of a basement or crawl space job. If you're finishing the basement, the rim gets sealed and insulated before the walls are framed and closed in. See basement and rim joist insulation.
Talk it through with Joe
Call or text me at (631) 492-0214, Monday to Saturday, 7 AM to 7 PM. I answer my own phone and call back the same day. Or request a free estimate and diagnosis. I'll go into the basement or crawl space, measure, and show you on the thermal camera where the cold air is getting in. We do this work across Nassau and Suffolk, from Brookhaven to Southold. Find your town on our service areas page.